Appliance Repair Forums
Free appliance repair
advice from the pros!
Find your appliance
parts at PartSelect.com
  Discuss

Kenmore Calypso Washer - Error Codes "Sr" and "Ld"

in the Washer Repair forum.
  

"I have a Kenmore Calypso Washer that first displayed a "Sr" error code. ..."


Go Back   Appliance Repair Forums > Appliance Repair Help > Washer Repair
Reply All information and advice in these forums is not intended to replace
an on-site diagnosis from a qualified appliance service technician.
 
LinkBack Thread Tools Search this Thread

Kenmore Calypso Washer - Error Codes "Sr" and "Ld"
Old 05-13-2008, 12:15 AM   #1
Janderson
Junior Member
Apprentice DIYer
 
Janderson is offline
Join Date: May 2008
Posts: 1
Janderson is on a distinguished road
Default Kenmore Calypso Washer - Error Codes "Sr" and "Ld"
Brand: Kenmore
Model Number: 110.22062102
Age: 1 - 4 years

I have a Kenmore Calypso Washer that first displayed a "Sr" error code. I stopped the cycle and tried to run it again and an "Ld" error code was displayed. The washer fills with water and then stops.

I checked the drain hose and found no blockage. I also drained the washer and started the process over with no luck. I checked the repair parts list for a relay switch and could find none. Any suggestions would be appreciated. I would like to try tackle this fix myself.

Thanks in advance.

Jason
 
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Appliance Parts

Find your appliance
parts at PartSelect.com

Old 05-14-2008, 05:32 PM   #2
PS Staff - Sheila
Service Technician
Master DIYer
 
PS Staff - Sheila's Avatar
 
PS Staff - Sheila is offline
Join Date: Apr 2007
Posts: 8,077
PS Staff - Sheila is on a distinguished road
Default

The Sr code stands for a stuck relay.

The relay is on the machine control board.

The Ld code stands for long drain time and because the washer will not drain the code will show.

Here is a link to the parts of your washer model 110.22062102.
 
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote

Old 06-02-2008, 05:47 AM   #3
lunatech
Junior Member
Apprentice DIYer
 
lunatech is offline
Join Date: Jun 2008
Posts: 1
lunatech is on a distinguished road
Default

Quote:
Originally Posted by Janderson View Post
I have a Kenmore Calypso Washer that first displayed a "Sr" error code. I stopped the cycle and tried to run it again and an "Ld" error code was displayed. The washer fills with water and then stops.

I checked the drain hose and found no blockage. I also drained the washer and started the process over with no luck. I checked the repair parts list for a relay switch and could find none. Any suggestions would be appreciated. I would like to try tackle this fix myself.

Thanks in advance.

Jason
Jason,
I am having the same problem with mine. When you clear the error code and try again do you hear a humming noise for awhile then the error code comes back? If you do, it might be what I have found. Drain all the water out by removing the back plate and releasing the drain hose. Lay the washer on its side (get help if needed) remove the bottom plate (3 screws) You should see an assembly with two hoses attached. This is the pump assembly. Release both hoses & side clips (clips will fly!) Pull to remove. The teeth are stripped that attach to the motor. I am currently trying to find a local parts supply and prices for this part when I came accross your posting. I have also found many complains about this brand & model. I bought mine in 2005 with only two minor repairs since (which were covered). But this time I will need to spend some money on this repair. Hope this helps.

Lunatech
 
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Appliance Parts

Find your appliance
parts at PartSelect.com
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Error code "1H" flashing Donsweeneyny Dishwasher Repair 2 06-05-2008 01:14 AM
Kenmore Calyopso washer shuts down with an error code "c1" Steve Hollberg Washer Repair 6 10-30-2007 01:32 AM
Will not run - "DOOR" error displayed WPMike Microwave Repair 2 10-11-2007 06:27 PM
Microwave built in "Door" error aimsal Microwave Repair 2 10-11-2007 06:18 PM
Error Codes "F1" and "F80" bk1golfer Dishwasher Repair 1 09-18-2007 05:12 PM



All information and advice in these forums is not intended to replace an on-site diagnosis from a qualified appliance service technician.
All times are GMT. The time now is 08:58 AM.

vBulletin skin developed by: eXtremepixels
Powered by vBulletin® Version 3.6.5
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.0.0
| Home | Register | FAQ | Members List | Calendar | Today's Posts | SEARCH | New Posts |

1 2 3 4 5 6 7 8 9 10 11 12